Warning Icon

For other alternatives, please contact us for more information.

0 Alternative products available

2VV-33B-R4

8-port multibeam antenna, 8x 1695–2690 MHz, 4x 33° HPBW, 4x RET

Find a Partner
Specifications
Finish making your selections or clear them to view relevant specifications.
Features and Benefits
  • Enhances network capacity and spectrum utilization when used in six sector applications
  • Reduces antenna count to minimize Cap-Ex and Op-Ex costs – 3 antennas required for 6 sector configurations

General Specifications

Antenna Type Multibeam
Band Single band
Color Light Gray (RAL 7035)
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material Fiberglass, UV resistant
Radiator Material Low loss circuit board
RF Connector Interface 4.3-10 Female
RF Connector Location Bottom
RF Connector Quantity, high band 8
RF Connector Quantity, mid band 0
RF Connector Quantity, low band 0
RF Connector Quantity, total 8

Remote Electrical Tilt (RET) Information

RET Hardware CommRET v2
RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 1 female | 1 male
Input Voltage 10–30 Vdc
Internal RET High band (4)
Power Consumption, idle state, maximum 1 W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)

Dimensions

Width 395 mm | 15.551 in
Depth 228 mm | 8.976 in
Length 1999 mm | 78.701 in
Net Weight, without mounting kit 27.1 kg | 59.745 lb

Array Layout

Click on image to enlarge.

Port Configuration

Click on image to enlarge.

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 1695 – 2690 MHz
Polarization ±45°
Total Input Power, maximum 1,200 W

Electrical Specifications

Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400 2490–2690
Beam Centers, Horizontal, degrees ±27 ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 39 38 36 35 31
Beamwidth, Vertical, degrees 9.9 9.3 8.8 7.8 7.1
Beam Tilt, degrees 2–12 2–12 2–12 2–12 2–12
USLS (First Lobe), dB 17 16 16 19 18
Front-to-Back Ratio at 180°, dB 32 34 35 33 32
Isolation, Cross Polarization, dB 27 27 27 27 27
Isolation, Inter-band, dB 28 28 28 28 28
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150
Input Power per Port at 50°C, maximum, watts 200 200 200 200 200

Mechanical Specifications

Wind Loading @ Velocity, frontal 403.0 N @ 150 km/h (90.6 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral 294.0 N @ 150 km/h (66.1 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum 689.0 N @ 150 km/h (154.9 lbf @ 150 km/h)
Wind Loading @ Velocity, rear 414.0 N @ 150 km/h (93.1 lbf @ 150 km/h)
Wind Speed, maximum 241 km/h (150 mph)

Packaging and Weights

Width, packed 505 mm | 19.882 in
Depth, packed 386 mm | 15.197 in
Length, packed 2124 mm | 83.622 in
Weight, gross 40.5 kg | 89.287 lb

Regulatory Compliance/Certifications

Agency Classification
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
ROHS Compliant
CHINA-ROHS Below maximum concentration value
REACH-SVHC Compliant as per SVHC revision on www.commscope.com/ProductCompliance
UK-ROHS Compliant, Compliant/Exempted

General Specifications

Antenna Type Multibeam
Band Single band
Color Light Gray (RAL 7035)
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material Fiberglass, UV resistant
Radiator Material Low loss circuit board
RF Connector Interface 4.3-10 Female
RF Connector Location Bottom
RF Connector Quantity, high band 8
RF Connector Quantity, mid band 0
RF Connector Quantity, low band 0
RF Connector Quantity, total 8

Remote Electrical Tilt (RET) Information

RET Hardware CommRET v2
RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 1 female | 1 male
Input Voltage 10–30 Vdc
Internal RET High band (4)
Power Consumption, idle state, maximum 1 W
Power Consumption, normal conditions, maximum 8 W
Protocol 3GPP/AISG 2.0 (Single RET)

Dimensions

Width 395 mm | 15.551 in
Depth 228 mm | 8.976 in
Length 1999 mm | 78.701 in
Net Weight, without mounting kit 27.1 kg | 59.745 lb

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 1695 – 2690 MHz
Polarization ±45°
Total Input Power, maximum 1,200 W

Electrical Specifications

Frequency Band, MHz 1695–1880 1850–1990 1920–2180 2300–2400 2490–2690
Beam Centers, Horizontal, degrees ±27 ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 39 38 36 35 31
Beamwidth, Vertical, degrees 9.9 9.3 8.8 7.8 7.1
Beam Tilt, degrees 2–12 2–12 2–12 2–12 2–12
USLS (First Lobe), dB 17 16 16 19 18
Front-to-Back Ratio at 180°, dB 32 34 35 33 32
Isolation, Cross Polarization, dB 27 27 27 27 27
Isolation, Inter-band, dB 28 28 28 28 28
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150
Input Power per Port at 50°C, maximum, watts 200 200 200 200 200

Mechanical Specifications

Wind Loading @ Velocity, frontal 403.0 N @ 150 km/h (90.6 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral 294.0 N @ 150 km/h (66.1 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum 689.0 N @ 150 km/h (154.9 lbf @ 150 km/h)
Wind Loading @ Velocity, rear 414.0 N @ 150 km/h (93.1 lbf @ 150 km/h)
Wind Speed, maximum 241 km/h (150 mph)

Packaging and Weights

Width, packed 505 mm | 19.882 in
Depth, packed 386 mm | 15.197 in
Length, packed 2124 mm | 83.622 in
Weight, gross 40.5 kg | 89.287 lb
Click on image to enlarge.
Click on image to enlarge.

Regulatory Compliance/Certifications

Agency Classification
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
ROHS Compliant
CHINA-ROHS Below maximum concentration value
REACH-SVHC Compliant as per SVHC revision on www.commscope.com/ProductCompliance
UK-ROHS Compliant, Compliant/Exempted

Assembly Drawing

Product Specification

Assembly Drawing

Product Specification