Warning Icon

For other alternatives, please contact us for more information.

0 Replacement products available

EGYHHTT-65B-R6

14-port, 1.8m, multiband antenna, RF port assignments are as follows: R1 = 694–862, R2 = 880–960, G1 = 1427-1518, B1 & B2 = 1695–2180 and Y1 & Y2 = 2490-2690 MHz, 65° horizontal beamwidth, 6x Internal RET. Y1 & Y2 share a common RET
Specifications
Finish making your selections or clear them to view relevant specifications.
How to Buy
Features and Benefits
  • Electrical tilt settings applicable to RF Ports R1, R2, G1, B1 & B2 can be set independently (See Array Layout and RET Table below)
  • A common electrical tilt setting is shared by RF Ports Y1 & Y2
  • All Internal RET actuators are connected in “Cascaded SRET” configuration
Specifications

General Specifications

Antenna Type Sector
Polarization ±45°
Band Multiband
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material Fiberglass, UV resistant
RF Connector Interface 4.3-10 Female
RF Connector Location Bottom
RF Connector Quantity, high band 10
RF Connector Quantity, low band 4
RF Connector Quantity, total 14

Remote Electrical Tilt (RET) Information, General

RET Hardware CommRET v1
RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 1 female | 1 male

Dimensions

Width 350 mm | 13.78 in
Length 1828 mm | 71.969 in
Depth 208 mm | 8.189 in

Array Layout

Click on image to enlarge.

Port Configuration

Click on image to enlarge.

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 694 – 862 MHz | 880 – 960 MHz | 1427 – 1518 MHz | 1695 – 2180 MHz | 2490 – 2690 MHz
Total Input Power, maximum 800 W @ 50 °C

Remote Electrical Tilt (RET) Information, Electrical

Protocol 3GPP/AISG 2.0 (Single RET)
Power Consumption, idle state, maximum 1 W
Power Consumption, normal conditions, maximum 8 W
Input Voltage 10–30 Vdc

Electrical Specifications

R1 R2 G1 B1 B2 Y1 Y2
Frequency Band, MHz 694–862 880–960 1427–1518 1695–2180 1695–2180 2490–2690 2490–2690
Gain, dBi 14.8 15.1 16.3 17.9 17.2 17.4 17.9
Beamwidth, Horizontal, degrees 67 63 64 61 61 62 60
Beamwidth, Vertical, degrees 11.9 10.1 7 5.2 5.2 4.1 4.1
Beam Tilt, degrees 2–14 2–14 2–12 2–12 2–12 2–12 2–12
USLS (First Lobe), dB 14 17 19 19 18 21 21
Front-to-Back Ratio at 180°, dB 30 31 33 31 34 29 33
Isolation, Cross Polarization, dB 28 28 28 28 28 28 28
Isolation, Inter-band, dB 30 30 30 30 30 30 30
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port, maximum, watts 350 350 300 300 300 250 250

Electrical Specifications, BASTA

Frequency Band, MHz 694–862 880–960 1427–1518 1695–2180 1695–2180 2490–2690 2490–2690
Gain by all Beam Tilts, average, dBi 14.5 14.9 16.0 17.4 16.8 17.1 17.7
Gain by all Beam Tilts Tolerance, dB ±0.5 ±0.4 ±0.6 ±0.8 ±0.7 ±0.5 ±0.3
Gain by Beam Tilt, average, dBi 2 ° | 14.5
8 ° | 14.5
14 ° | 14.4
2 ° | 14.9
8 ° | 14.9
14 ° | 14.7
2 ° | 15.8
7 ° | 16.0
12 ° | 16.0
2 ° | 17.3
7 ° | 17.5
12 ° | 17.3
2 ° | 16.7
7 ° | 16.9
12 ° | 16.6
2 ° | 17.2
7 ° | 17.3
12 ° | 16.7
2 ° | 17.7
7 ° | 17.9
12 ° | 17.4
Beamwidth, Horizontal Tolerance, degrees ±1.8 ±2 ±7.2 ±3.5 ±3.8 ±3.5 ±4
Beamwidth, Vertical Tolerance, degrees ±1.4 ±0.4 ±0.3 ±0.5 ±0.6 ±0.3 ±0.2
USLS, beampeak to 20° above beampeak, dB 14 17 18 16 15 16 15
Front-to-Back Total Power at 180° ± 30°, dB 25 23 24 26 28 24 26
CPR at Boresight, dB 18 20 14 21 21 20 22
CPR at Sector, dB 10 9 6 8 6 7 9

Material Specifications

Reflector Material Aluminum

Mechanical Specifications

Wind Loading at Velocity, frontal 67.7 lbf @ 150 km/h | 301.0 N @ 150 km/h
Wind Loading at Velocity, lateral 57.1 lbf @ 150 km/h | 254.0 N @ 150 km/h
Wind Loading at Velocity, maximum 638.0 N @ 150 km/h | 143.4 lbf @ 150 km/h
Wind Speed, maximum 241 km/h | 149.75 mph

Packaging and Weights

Width, packed 456 mm | 17.953 in
Depth, packed 357 mm | 14.055 in
Length, packed 1975 mm | 77.756 in
Net Weight, without mounting kit 33 kg | 72.752 lb
Weight, gross 46.5 kg | 102.515 lb

Regulatory Compliance/Certifications

Agency Classification
CE Compliant with the relevant CE product directives
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
ROHS Compliant/Exempted
CHINA-ROHS Above maximum concentration value

General Specifications

Antenna Type Sector
Polarization ±45°
Band Multiband
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material Fiberglass, UV resistant
RF Connector Interface 4.3-10 Female
RF Connector Location Bottom
RF Connector Quantity, high band 10
RF Connector Quantity, low band 4
RF Connector Quantity, total 14

Remote Electrical Tilt (RET) Information, General

RET Hardware CommRET v1
RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 1 female | 1 male

Dimensions

Width 350 mm | 13.78 in
Length 1828 mm | 71.969 in
Depth 208 mm | 8.189 in

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 694 – 862 MHz | 880 – 960 MHz | 1427 – 1518 MHz | 1695 – 2180 MHz | 2490 – 2690 MHz
Total Input Power, maximum 800 W @ 50 °C

Remote Electrical Tilt (RET) Information, Electrical

Protocol 3GPP/AISG 2.0 (Single RET)
Power Consumption, idle state, maximum 1 W
Power Consumption, normal conditions, maximum 8 W
Input Voltage 10–30 Vdc

Electrical Specifications

R1 R2 G1 B1 B2 Y1 Y2
Frequency Band, MHz 694–862 880–960 1427–1518 1695–2180 1695–2180 2490–2690 2490–2690
Gain, dBi 14.8 15.1 16.3 17.9 17.2 17.4 17.9
Beamwidth, Horizontal, degrees 67 63 64 61 61 62 60
Beamwidth, Vertical, degrees 11.9 10.1 7 5.2 5.2 4.1 4.1
Beam Tilt, degrees 2–14 2–14 2–12 2–12 2–12 2–12 2–12
USLS (First Lobe), dB 14 17 19 19 18 21 21
Front-to-Back Ratio at 180°, dB 30 31 33 31 34 29 33
Isolation, Cross Polarization, dB 28 28 28 28 28 28 28
Isolation, Inter-band, dB 30 30 30 30 30 30 30
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port, maximum, watts 350 350 300 300 300 250 250

Electrical Specifications, BASTA

Frequency Band, MHz 694–862 880–960 1427–1518 1695–2180 1695–2180 2490–2690 2490–2690
Gain by all Beam Tilts, average, dBi 14.5 14.9 16.0 17.4 16.8 17.1 17.7
Gain by all Beam Tilts Tolerance, dB ±0.5 ±0.4 ±0.6 ±0.8 ±0.7 ±0.5 ±0.3
Gain by Beam Tilt, average, dBi 2 ° | 14.5; 8 ° | 14.5;14 ° | 14.4 2 ° | 14.9; 8 ° | 14.9;14 ° | 14.7 2 ° | 15.8; 7 ° | 16.0;12 ° | 16.0 2 ° | 17.3; 7 ° | 17.5;12 ° | 17.3 2 ° | 16.7; 7 ° | 16.9;12 ° | 16.6 2 ° | 17.2; 7 ° | 17.3;12 ° | 16.7 2 ° | 17.7; 7 ° | 17.9;12 ° | 17.4
Beamwidth, Horizontal Tolerance, degrees ±1.8 ±2 ±7.2 ±3.5 ±3.8 ±3.5 ±4
Beamwidth, Vertical Tolerance, degrees ±1.4 ±0.4 ±0.3 ±0.5 ±0.6 ±0.3 ±0.2
USLS, beampeak to 20° above beampeak, dB 14 17 18 16 15 16 15
Front-to-Back Total Power at 180° ± 30°, dB 25 23 24 26 28 24 26
CPR at Boresight, dB 18 20 14 21 21 20 22
CPR at Sector, dB 10 9 6 8 6 7 9

Material Specifications

Reflector Material Aluminum

Mechanical Specifications

Wind Loading at Velocity, frontal 67.7 lbf @ 150 km/h | 301.0 N @ 150 km/h
Wind Loading at Velocity, lateral 57.1 lbf @ 150 km/h | 254.0 N @ 150 km/h
Wind Loading at Velocity, maximum 638.0 N @ 150 km/h | 143.4 lbf @ 150 km/h
Wind Speed, maximum 241 km/h | 149.75 mph

Packaging and Weights

Width, packed 456 mm | 17.953 in
Depth, packed 357 mm | 14.055 in
Length, packed 1975 mm | 77.756 in
Net Weight, without mounting kit 33 kg | 72.752 lb
Weight, gross 46.5 kg | 102.515 lb
Click on image to enlarge.
Click on image to enlarge.

Regulatory Compliance/Certifications

Agency Classification
CE Compliant with the relevant CE product directives
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
ROHS Compliant/Exempted
CHINA-ROHS Above maximum concentration value
Documentation & Downloads

Assembly Drawing

Environment Health and Safety

Installation Instruction

Product Information

Product Specification

Product Specification (Comprehensive)

Warranty

Other Ways to Browse

Browse by Application

Browse by Application